- Definition
- Age criteria
- Liquid petroleum gas (LPG)
- Doors
- Doorways
- Access to doors
- Emergency doors
- Steps
- Interior
- Interior illumination
- Grab handles and rails
- Seats
- Removable seats
- Seat occupant safety harness
- Carriage of passengers in wheelchairs
- Passengers in wheelchairs - access/egress of vehicle
- Requirement for ramps
- Requirements for lifts
- Removeable seats and vacant wheelchairs
- Marking of carrying capacity
- Passengers
- Stowage of equipment
- Fire extinguishing apparatus
- First aid equipment
- Security cameras inside vehicles (CCTV)
- Reversing bleeper
- Signs and markings
- Windows
- Mirrors
- Exhaust pipes
- Variance
1. Definition
Minibus Category M2, A standard right hand drive vehicle for the purpose of these conditions, relates to a heavy motor vehicle capable of carrying more than eight passengers (seated) or passengers in wheelchairs. A certificate of conformity is required for vehicles converted to carry wheelchairs.
A vehicle licence will not normally be granted if it has sustained accident damage resulting in structural distortion beyond the accepted limits of the vehicle manufacturer, or, has been disposed of under an insurance salvage agreement (categories A,B,N or S).
2. Age criteria
(a) Vehicles being licensed for the first time
The age of a vehicle, for licensing purposes, shall be determined by the date of first registration on the V5 document (log book). A vehicle will only be accepted for licensing if the date of first registration is less than 7 years from the date of application and meets lower emission (euro 5 petrol, euro 6 diesel, hybrid, diesel hybrid engine vehicles or full electric).
Vehicles being licensed for the first time must be licensed for use within 28 days of the date of the new vehicle application inspection.
(b) Existing licensed vehicles seeking to be re-licensed (under 7 years old)
A currently licensed vehicle may continue to be re-licensed for up to 15 years from the date of first registration providing that all other licensing requirements relating to that vehicle have been complied with, any break in the licence will result in part (a) of this condition coming into effect.
(c) Inspection policy for licensed vehicles seeking to be relicensed beyond 7 years
A currently licensed vehicle may continue to be re-licensed beyond 7 years with an end date of 15 years from the date of first registration, providing that it is:-
- In suitable mechanical condition
- Safe
- Comfortable
and meets all licensing conditions. This will be determined by a formal inspection by an Authorised Vehicle Examiner of the Taxi and Private Hire Licensing Section.
It is the responsibility of the vehicle proprietor to ensure that vehicle inspection arrangements are in place prior to the expiry of the vehicle licence, allowing sufficient time for both the inspection and any remedial work to be completed prior to the expiry date.
Inspections will be carried out in accordance with the DVSA class 5 testing and these conditions.
3. Liquid petroleum gas (LPG)
Vehicles with Dual Fuel or ‘aftermarket’ Liquid Petroleum Gas (LPG) systems must be tested, certified and recognised by Liquid Gas UK, a valid insurance and current V5 acknowledging the LPG conversion must be provided.
For new Private Hire vehicle licence applications, all certifications and documents must be produced at the time of application. For vehicles that are wanting to install an LPG system during the currency of a Private Hire vehicle licence, they must inform the Taxi and Private Hire Licensing Section in writing and produce the above certification and book the vehicle in for an inspection within 7 days of installation.
LPG conversions fitted to petrol Hybrid vehicle will not be accepted unless fitted as standard by the vehicle manufacturer.
4. Doors
(Ref: The Public Service Vehicle Accessibility Regulations 2000 and The Road Vehicles (Construction and Use) Regulations 1986)
Shall be fitted with 4 doors:
(a) One service door on the nearside of the vehicle in addition to the passenger front nearside door, and one emergency door either at the rear or on the offside of the vehicle, however, any emergency door fitted on the offside of the vehicle shall be in addition to the driver’s door. Any rear door which separated into two shall be treated for the purposes of this condition as one door.
(b) No vehicle shall be fitted with any door on the offside other than the driver’s door and emergency door.
(c) On all passenger doors the method of opening and direction of opening
should be clearly marked on the inside and outside of the vehicle. Markings must be in a contrasting colour to the surrounding background and lettering should be at least 20mm high.
5. Doorways
(Ref: The Public Service Vehicle Accessibility Regulations 2000 and The Road Vehicles (Construction and Use) Regulations 1986)
Doorways for use by passengers in wheelchairs must have a width of 800mm and a headroom in the centre of the doorway of 1400mm.
6. Access to doors
There shall be unobstructed minimum of 12 inches (gangway) access from every passenger seat to at least two doors one of which must be on the nearside of the vehicle, except in the case of the driver seat and the nearside passenger seat.
7. Emergency doors
(Ref: The Public Service Vehicle Accessibility Regulations 2000 and The Road Vehicles (Construction and Use) Regulations 1986)
The emergency door shall be clearly marked in letters not less than 25mm high on both the inside and outside stating “EMERGENCY DOOR” or “FOR EMERGENCY USE ONLY” and the means of operation shall be clearly indicated on or near the door. The door must if hinged open outwards, be capable of opening manually and when fully opened give an aperture in the body of the vehicle not less than 1210mm high nor less than 530mm wide.
8. Steps
(Ref: The Public Service Vehicle Accessibility Regulations 2000 and The Road Vehicles (Construction and Use) Regulations 1986)
Steps must be fitted to the service and emergency doors which shall be no higher than 250mm from the ground wherever possible. All steps must be covered in non-slip material and flush fitting.
There must be no more than 3 steps into the vehicle.
All steps must be permanently secured to the vehicle at the point of entry, the vertical distance between the adjacent steps and between any final step and the interior floor of the vehicle must be between 120mm and 200mm.
All steps must present a useable surface at last 400mm wide and 280mm deep.
The surface of all steps must be slip resistant. Step nosing must be designed to minimise risk of tripping and must be in a contrasting tone and colour(s) to the step surface.
No step, lift or ramp fitted to the side of a vehicle may project more than 100mm beyond the widest part of the vehicle (disregarding mirrors) when the vehicle is in motion.
Any step (fixed or retractable) must be constructed and secured to the vehicle in such a way as to withstand, with no permanent deformation, the application of a weight at its centre of:
125kg, in the case of a step designed for one person and 250kg, in the case of a step designed to accommodate one person and one assistant.
9. Interior
All minibuses shall be fitted with a soft headlining front to rear, side panels to be suitably panelled floor to roof leaving no sharp edges or gaps. The floor area to be covered with non-slip material with no gaps or edges. All material used must be fire resistant.
10. Interior illunination
(Ref: The Public Service Vehicle Accessibility Regulations 2000 and The Road Vehicles (Construction and Use) Regulations 1986)
All steps must be automatically illuminated when the relevant door is opened. Lamps shall be fitted which can be manually operated to illuminate all gangways.
All interior lighting must be fully operational and illuminate when the passengers doors open.
11. Grab handles and rails
(Ref: The Public Service Vehicle Accessibility Regulations 2000 and The Road Vehicles (Construction and Use) Regulations 1986)
There shall be at least one grab handle and one hand rail to the service door areas to assist the passengers to get on and off the vehicle. They shall be fitted in such a way that they do not obstruct the entrance or impede access or egress in any way. All such grab handles/rails must be coated in a bright high visibility non-slip coating which will contrast in colour with the interior of the vehicle.
12. Seats
(Ref: The Public Service Vehicle Accessibility Regulations 2000 and The Road Vehicles (Construction and Use) Regulations 1986)
All seats must be forward facing and have available inertia reel lap and diagonal seat belts. All seat belts must comply with the technical and installation requirements of the relevant U.K. or European Directives.
13. Removable seats
Seats may be mounted on tracking fastened to the floor of the vehicle using Unwin Safety Systems Seat Fixings or a similar make approved by the Vehicle Licensing & Enforcement Section. These seats can be removed or replaced as necessary to allow space for one or more wheelchairs.
Tracking must be correctly aligned and spaced to allow easy removal of the seat. Fastenings for the track must be to the manufacturers specification and hold a certificate of conformity.
14. Seat occupant safety harness
(Ref: The Public Service Vehicle Accessibility Regulations 2000 and The Road Vehicles (Construction and Use) Regulations 1986)
A full static harness or a lap and diagonal inertia reel belt must be available for each wheelchair passenger. These items will engage into the same floor tracking as the wheelchair restraints and all such equipment should be fully adjustable for the safety and comfort of the wheelchair passengers and quickly releasable in an emergency.
15. Carriage of passengers in wheelchairs
(Ref: The Public Service Vehicle Accessibility Regulations 2000 and The Road Vehicles (Construction and Use) Regulations 1986)
A space adequate to accommodate the dimensions of at least a size A wheelchair must be available in order that it may be manoeuvred from the gangway into position without catching passenger feet or chair wheels and provides a reasonable amount of space for the passenger during the journey in accordance with U.K. and European Codes of Practice. Occupied passenger wheelchairs must be restrained by an approved method in accordance with the manufacturer’s instructions.
16. Passengers in wheelchairs - access/egress of vehicle
Folding ramps must be available for those vehicles whose floor height allows a convenient gradient. (No higher than 520mm (20.4 inches)). Ramps should be as long as possible to give the best possible gradient of at least 1:4 rear entry 1:3 side entry.
17. Requirement for ramps
(Ref: The Public Service Vehicle Accessibility Regulations 2000 and The Road Vehicles (Construction and Use) Regulations 1986)
17.1 Any vehicle with a floor height greater than 520mm (20.4 inches) should be fitted with a side or rear approved tail lift platform. (BA 6109 PART 2 Category A or B only, or its European Equivalent).
17.2 Channel ramps will be not permitted.
17.3 The ramp surface should be covered with non-slip material. Side edges of the ramp shall be provided with flanges at least 25mm high to prevent the wheelchair rolling off.
17.4 The edges of the ramp surface shall be marked in a high-contrast colour scheme.
17.5 The ramp shall have a minimum safe working load of 300kg.
17.6 When in use the ramp must be securely located at the point of wheelchair entry.
17.7 Ramps must be stowed in a way which does not obstruct any handle or other opening device for any exit and such that in the event of an accident it could not cause injury to either passengers or the driver. If the ramp obstructs an exit, it must also be capable of being manually pushed or pulled out of the way from the inside and outside when the door is open so as to leave the doorway clear for use in an emergency.
18. Requirements for lifts
(Ref: The Public Service Vehicle Accessibility Regulations 2000)
18.1 Lift platforms shall be of sufficient size to accommodate an occupant in the reference wheelchair. The lift surface should be covered with non-slip material. Side edges of the lift platform shall be provided with flanges at least 25mm high to prevent the wheelchair rolling off. The rear edge shall incorporate a device at least 100mm high to prevent rolling off which becomes effective when the lift leaves the ground.
18.2 The edges of the lift surface shall be marked in a high contrast colour scheme.
18.3 If power operated, the lift shall have a manual means of operation in the
event of a power failure. Lifts complying with BS 6109 shall be considered to meet all the above criteria.
18.4 Lifts must be stowed in a way which does not obstruct any handle or other opening device for any exit and such that in the event of an accident it could not cause injury to either passengers or the driver. If the lift obstructs an exit, it must also be capable of being manually pushed or pulled out of the way from the inside and outside when the door is open so as to leave the doorway clear for use in an emergency.
18.5 Any controls for the operation of a lift must be inhibited while the vehicle is in motion and may only be operated at the point where the boarding device is fitted either by the driver or by an individual under their supervision.
18..6 The lift shall have a minimum safe working load of 300kg.
18.7 Where a vehicle is fitted with a power operated lift, the proprietor of the vehicle shall produce to the Council’s vehicle inspector on each occasion hat the vehicle is presented for testing by the Council, a valid test certificate for such lift in accordance with the requirements of the Lifting Operations and Lifting Regulations 1998 (LOLER). These regulations require that the passenger lifts are tested and certified as fit by a competent person every six months.
19. Removeable seats and vacant wheelchairs
Seats not properly attached to the vehicle by the manner in which they were designed must not be carried in the vehicle. Unoccupied wheelchairs folded or otherwise must be securely fastened to the body of the vehicle by means of straps or clamps designed for that purpose.
20. Marking of carrying capacity
Markings of passenger carrying capacity should be clearly marked with letters not less than 25mm in height which may be read from inside and outside the vehicle with the maximum passenger seating and passenger wheelchair capacity of the vehicle. Examples: 8+0 or 6+1 or 4+2.
The combined total of conventional seats (occupied or otherwise) and passengers in their wheelchairs must not exceed the maximum stated on the licence.
21. Passengers
This Authority is responsible for deciding how many passengers a taxi or private hire vehicle is licensed to carry. Whilst the Vehicle Registration Certificate (V5C) issued by the Driver and Vehicle Licensing Agency states the seating capacity of a vehicle, licensing authorities are entitled to restrict the passenger carrying capacity in the interest of convenience and comfort. When considering limiting the passenger carrying capacity on the grounds of comfort
Each person transported in the vehicle regardless of age will be regarded as a separate passenger, the number of passengers must not exceed the total number of passengers the vehicle is licensed to transport.
The seating capacity will be determined by the Licensing Authority and will be based upon the manufacturer’s specification as stated in the V5C document, the orientation of the seating, the dimensions of the seating, passenger safety and comfort.
22. Stowage of equipment
Space should be provided for safe stowage of restraint systems when not in use where they will not present a hazard to passengers and will not obstruct gangways or exits. There should be no loose items in the vehicle which will present a hazard to passengers when in use.
23. Fire extinguishing apparatus
The vehicle shall carry at all times two fire extinguishers which comply with the specification British Standard Institution number BS 5423 or its European equivalent, must be foam spray 0.9 litre AFFF (RATING-21B), complete with special transport bracket and fitted in a suitable prominent safe position inside the vehicle for ease of use by the driver and passengers. Fire extinguishers must at all times be fully charged and ready for use and hold a current inspection certificate. It is the responsibility of the proprietor to ensure that the fire extinguishers are inspected and issued certificates.
24. First aid equipment
The vehicle shall carry at all times a first aid receptacle which has two pairs of surgical gloves, ten antiseptic wipes foil packed, one conforming disposable bandage (not less than 7.5cm wide), two triangular bandages, one pack of 24 assorted adhesive dressings, three large sterile non-medicated ambulance dressings (not less than 15.0 x 20.0 cm), two sterile eye pads with attachments, twelve assorted safety pins and one pair of rust-free blunt-ended scissors all stored in a prominent labelled position on view to the driver and passengers.
25. Security cameras inside vehicles (CCTV)
The main issues in respect of a safety camera fitted to a vehicle are set out below: -
(a) Will be of a make, type and design previously approved by Authorised Officers of the Council and on the ‘Approved List’ maintained by the Taxi and Private Hire Licensing Section.
(b) Will not be changed in any way from its original design, be free of
damage and maintained in working condition.
(c) The vehicle will carry appropriate signs, approved by Authorised Officers, informing the public that camera surveillance is active in the vehicle.
(d) The recording system and memory card (or other image memory recording system) will be securely stored within the vehicle and away from public access.
(e) Installation and maintenance must be in accordance with manufacturer’s specifications and recommendations.
(f) The images contained in the recording device may only be downloaded by an Authorised Officer of the Council or Police Officer.
(g) Dashcams are only permitted to face outwards at the road ahead, any rear dashcams MUST be mounted in the rear window area facing outwards only. All dashcam must NOT have the audio recording function active at any time.
Further guidance and policy document can be found on our webpages and on the Information Commissioners Office (ISO) website surveillance in vehicles.
26. Reversing bleeper
Shall be fitted with a reversing bleeper (night silent).
27. Signs and markings
No Smoking signs- a minimum of 2 no smoking signs must be displayed at all times, these must be on a white background and visible from outside the vehicle
The International Wheelchair sign measuring 160mm x 160mm and featuring a white symbol on a blue background. This must be displayed in the rear and side windows so as to be clearly visible.
No signs, notices, advertisements, plates, marks, numbers, letters, figures, symbols, emblems or devices whatsoever shall be displayed on, in or from the vehicle except as may be required by any statutory provision of these conditions.
28. Windows
Shall be fitted with 2 or 3 windows depending on the length of the vehicle to both the nearside and offside, with full sliding openings and fitted with approved non tinted safety glass giving all round vision to the outside. The windscreen must have a minimum light transmission of 75% and all other windows must have a minimum light transmission of 70%.
29. Mirrors
Shall be fitted with mirrors so that the driver when occupying the driver’s seat can clearly see the area immediately inside and outside every service door, emergency door and passenger door to the vehicle. A rear door glass slope mirror to be fitted.
30. Exhaust pipes
The outlet of every exhaust pipe fitted shall be either at the rear or on the offside of the vehicle.
31. Variance
Should a proprietor of a minibus apply for a private hire vehicle licence and the specification of the vehicle varies from those laid down in Council conditions, a variation may be requested in writing but will be subject to approval in writing from the Vehicle Licensing Section of the Council.
Points of reference have been made using the following:
- The Road Vehicles (Construction and Use) Regulations 1986
- The Public Service Vehicles Accessibility Regulations 2000
- Local Government (Miscellaneous Provisions) Act 1976
- The Road Vehicles (Approval) Regulations 2020
- DFT Guidance for manufacturers and operators 2005
- DFT Best Practise Guidance 2023